Featured Categories

Home->BMS with Communications

3S-96S (11.1V~307.2V) BMS with Relay, with SMBus,I2C/HDQ communication protocol for Li-ion and Li-Polymer Battery Packs

Part number: HCX-D170V1 with Relay

Features and Benefits

 Programmable BMS with SMBus , I2C/HDQ Communication protocol

1.Battery Management System for 3S-96S (11.1V~355.2V) Li-ion and Li-Polymer battery pack;
2.BMS applies for 3S-96S configuration  Li-ion and Li-Polymer battery pack;
3.To prevent the battery packs from overcharge,overdischarge,over current, over temperature ,short circuit ;
4.With cell balance/equilibrium function;
5.Compatible with all the  Li-ion and Li-Polymer cells.
6.How balancing function works? after battery pack is fully charged. PCM will detect each cell's voltage and trim higher voltage down until other cells reach the same voltage level. Therefore, it helps cells have longer service life.
7.This BMS is designed for 3S ~ 96S Battery packs, can be used on Li-ion, Li-Polymer, LiFePO4, with max. continuous discharge @ 500A, and it is integrated with SMBUS, I2C, HDQ optional communications protocol for battery pack monitoring, fuel/gas gauge management, communicating with your applications, can accurately read your battery pack’s SOC and SOH information. The communication function is removable, can remove it if there is no need.
8.HCX-D170V1 with replay is designed as high current BMS, the mother board BMS works with the Relay, can carry 500A continuous current with DC voltage ranges from DC12V to DC720V, peak current can carry 2000A.

 

Specifications

Item

Contents

Criteria

(Adjustable)

1

Model

HCX-D170V1 with Relay

3S-96S

2

Voltage

Charging voltage

Adjustable with different configuration

3

Current

Maximal continuous charging current

200A (adjustable)

Maximal continuous discharging current

500A (adjustable)

Current consumption

≤200μA

 

4

Overcharge Protection

Over charge detection voltage

Adjustable(depends on battery type)

Over charge detection delay time

Adjustable(depends on battery type)

Over charge release voltage

Adjustable(depends on battery type)

5

Over Discharge Protection

Over discharge detection voltage

Adjustable(depends on battery type)

Over discharge detection delay time

Adjustable(depends on battery type)

Over discharge release voltage

Adjustable(depends on battery type)

6

Over Current Protection

Over current detection voltage

Adjustable(depends on battery type)

Over current detection current

Adjustable(depends on battery type)

Detection delay time

Adjustable(depends on battery type)

Release condition

Adjustable(depends on battery type)

7

Short Circuit Protection

Detection condition

Adjustable(depends on battery type)

Detection delay time

Adjustable(depends on battery type)

Release condition

Cut load, automatically recover

8

Balance/Equilibrium

Balance voltage for single cell

Adjustable(depends on battery type)

Balance current for single cell

Adjustable(depends on battery type)

9

Balancing ON/OFF

When the balancing LEDs are on then the balancing function will get started

10

Temperature

Operating temperature range

-40~+85°C

Storage temperature range

-20~ +125°C

11

Capacity Display

Press Battery Capacity checking Switch to dispaly capacity by LEDs

12

Size  (L*W*T)

L214.5mm*W143mm*T37mm

Connection Diagram

• Mother Board D170V1

HCX-D170V1 BMS mainly designed based on SEIKO and TI chips and MicroChip , the SMBus/Fuel Gauge is based on TI BQ34Z100, with HDQ, IIC communication interface, can be used on 3S-96S li-ion, li-poymer and lifepo4 battery packs, the removable communication module can be removed as an effective-cost solution.

• D170V1 Relay

HCX-D170V1 Relay is designed to be smallest, lightest weight, lowest cost sealed contactor in the industry with current rating 500A discharging.

Built-in coil economizer - only need to be powered by12V DC and it limits back EMF to 0 V.

Hermetically sealed - intrinsically safe, operates in explosive/harsh environmental with on oxidation or contamination of coils or contacts, including long-periods of non-operation.

 

( Layout dimension of D170V1 Relay)

 Battery Capacity Checking

Press the button switch to check battery pack’s capacity the LEDs will be turned on.
(Marked as RED arrow in the picture as below)
 
This BMS also can connect to our LCD display to check battery informations on our LCD, the LCD Display connection socket as marked in yellow arrow as above picture.
 
How balancing function works?
After battery pack is fully charged. PCM will detect each cell's voltage and trim higher voltage down until other cells reach the same voltage level. Therefore, it helps cells have longer service life.
Once the balancing get started, the balancing LEDs will be on automatically.(check red arrow marked in the pictures as below)
 
 
How to connect BMS to PC/laptop to set up all parameters and the communications.(on BMS, there is one socket for the communication adapter connections, check the picture as below )
 
 
Then connect our BMS with the communication convertor adapter, the commnuication conventor adaptor is called “EV2300/EV2400” which can be purchased from BesTech Power or from TI.
 
 
After installed the software to your PC/laptop, The PC-end-software (copyright belongs to TI) can Set and modifying all the logical parameters
 
 
 
 
 
 
 
 
Connections Diagram 
 
1) How to connect Relay with D170V1 BMS mother Board
 
2) Battery Pack with charger and Load ,BMS, Relay connection Diagram
 
 
3)The BMS connection for battery voltage detection cables ( 4S battery pack connection as example below)
 
 
 
 
This BMS is designed for multi-configurations pack, the mother controllers are tired up, the voltages-detection-cables go in the way as picture shown below:
 
 
Note:
Please connect B- of BMS to battery pack negative terminal then connect P+ to battery pack positive terminal, for the voltage detection cables, please connect from cell #1 till the last cell.
There is no warranty if there is any hardware changes from customers’ side, the configurations are changing on our hardware and software, please contact us for more details of the changes if customers insist to do DIY.
 
For more information, please email us at info@BesTechPower.com or sales@BesTechPower.com .
Thank you again for choosing BesTech Power!
 

www.BesTechPower.com - www.BesTekPower.com - www.BatteryPCM.com - www.LithiumBMS.com - www.BatteryBMS.com - www.LiTechPower.com (our on-line distributor)

Copyright © 2011 BesTech Power Co., Ltd.
Tel:+86 - 769 82033052     Fax:+86 - 769 82033050 # 620   E-mail:info@BesTechPower.com
Address 1: 3F, Bldg3, Fulian Industrial Park, Heping Industrial area, Jianhui Rd, Longhua, ShenZhen, China.
Address 2: 4F, Bldg B, RuiXin HengYe Industrial Park, TaiXing Rd # 18A, ShiGu District, TangXia Town, DongGuan, China